您现在正在浏览:首页 > 论文 > 机械机电 > 毕业设计-柴油机齿轮室盖钻镗专机总体设计

免费下载毕业设计-柴油机齿轮室盖钻镗专机总体设计

  • 资源类别:论文
  • 资源分类:机械机电
  • 适用专业:机械设计制造及自动化
  • 适用年级:大学
  • 上传用户:lihang1614
  • 文件格式:word+AutoCAD
  • 文件大小:1.00MB
  • 上传时间:2014-5-21 2:01:04
  • 下载次数:0
  • 浏览次数:0

安全检测:瑞星:安全 诺顿:安全 卡巴:安全

资料简介
毕业设计-柴油机齿轮室盖钻镗专机总体设计,正文共224页,12818字,附英文翻译、设计图纸。
摘 要:本课题设计一台加工柴油机齿轮室盖的钻镗组合机床,主要完成机床总体和右主轴箱的设计工作。
本课题设计的组合机床采用“一面两销”定位、液动夹紧,一次装夹加工柴油机齿轮室盖三个面上的孔,保证了加工精度,提高了生产效率,减少了工人的劳动强度。而且在设计之中,尽量选用通用件,减少了制造成本,增加了经济效益。
关键词:组合机床 主轴箱 主轴 传动轴 齿轮室盖

Abstract: This project is to design a modular machine tool for manufacturing the gear chamber cap of diesel engine. Mainly work is the design of overall and the right headstock.
According to the request of construction features, processing spot, size precision, surface roughness and productivity that diesel engine gear chamber cap, sets the machine tool for single location horizontal type modular machine tool. In order to guarantee the processing precision, the localization plan use "two sells and a surface". In order to implement the stepless speed regulation, safe is reliable, therefore choice hydraulic pressure sliding table. According the size of components and the eel cover, key and so on that in axis select standard letter by the corresponding number.
The modular machine tool of this project design use “two sells and one surface” to locate , hydraulic press and clamps. In the situation of one clamp, the holes three surface of the diesel engine gear chamber cap, are guaranteed the processing precision, is enhanced the production efficiency, is increased worker’s labor intensity. Moreover during the design, the standard parts are selected as far as possible, reduced the production cost and increased the economic efficiency.
Key words: modular machine tool headstock spindle drive shaft gear chamber cap

目 录
第一章绪论……(1)
1.1发展现状与趋势(1)
1.2问题的提出……(1)
1.3设计的几大组成部分……(1)
第二章组合机床总体设计……(2)
2.1 组合机床工艺方案的制定………(2)
2.2 组合机床配置型式及结构方案的确定……(2)
2.3 各侧具体零部件的设计、计算及选择……(2)
2.4 机床生产率计算卡……(9)
第三章 组合机床多轴箱设计……(11)
3.1 绘制右主轴箱设计原始依据图…(11)
3.2 主轴箱传动系统的设计与计算…(12)
3.3 多轴箱坐标计算、绘制坐标检查图………(17)
3.4 主轴箱中变位齿轮的计算………(20)
3.5 变位齿轮的设计………(20)
3.6齿轮强度校核 (22)
3.7 传动轴直径的确定和轴的强度校核………(24)
3.8 主轴箱体及其附件的选择设计…(27)
4 结论 (29)
参考文献(30)
致谢… (31)
资料文件预览
共2文件夹,10个文件,文件总大小:1.66MB,压缩后大小:1.00MB
  • 毕业设计-柴油机齿轮室盖钻镗专机总体设计
    • 柴油机齿轮室盖钻镗专机总体设计
      • AutoCAD工程图纸文件1.dwg  [109.04KB]
      • AutoCAD工程图纸文件2.dwg  [354.84KB]
      • AutoCAD工程图纸文件3.dwg  [63.44KB]
      • AutoCAD工程图纸文件4.dwg  [61.14KB]
      • Borland的Paradox 7表Thumbs.db  [5.50KB]
      • Windows临时文件~WRL0367.tmp  [56.00KB]
      • Microsoft Word文档外文翻译—2008.doc  [469.00KB]
      • Microsoft Word文档摘要—2008 2006.doc  [30.50KB]
      • Microsoft Word文档正文说明书—2008.doc  [525.00KB]
      • Microsoft Word文档毕_业_设_计(论文)封面2008.doc  [28.50KB]
下载地址
资料评论
注意事项
下载FAQ:
Q: 为什么我下载的文件打不开?
A: 本站所有资源如无特殊说明,解压密码都是www.xuehai.net,如果无法解压,请下载最新的WinRAR软件。
Q: 我的学海币不多了,如何获取学海币?
A: 上传优质资源可以获取学海币,详细见学海币规则
Q: 为什么我下载不了,但学海币却被扣了?
A: 由于下载人数众多,下载服务器做了并发的限制。请稍后再试,48小时内多次下载不会重复扣学海币。
下载本文件意味着您已经同意遵守以下协议
1. 文件的所有权益归上传用户所有。
2. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
3. 学海网仅提供交流平台,并不能对任何下载内容负责。
4. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
5. 本站不保证提供的下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
返回顶部