您现在正在浏览:首页 > 论文 > 机械机电 > 毕业论文-汽车差速器壳的三维造型及有限元分析

免费下载毕业论文-汽车差速器壳的三维造型及有限元分析

  • 资源类别:论文
  • 资源分类:机械机电
  • 适用专业:汽车零件设计
  • 适用年级:大学
  • 上传用户:jobwangwu
  • 文件格式:word
  • 文件大小:1.32MB
  • 上传时间:2011-12-9 23:53:18
  • 下载次数:1
  • 浏览次数:31

安全检测:瑞星:安全 诺顿:安全 卡巴:安全

资料简介
毕业论文-汽车差速器壳的三维造型及有限元分析,共38页,9595字
摘要:差速器壳设计是汽车设计中最重要、承载最复杂的运动件之一,对差速器壳的强度分析一直受到设计者的重视。由于差速器壳的几何形状、边界条件和作用载荷都非常复杂,按照传统的方法进行试验研究难度较大,这就要求我们采用新的研究方法来研究和分析差速器壳。
本文通过运用PROE绘图软件,绘制差速器壳三维实体模型,然后运用ANSYS分析软件对差速器壳进行强度分析,通过对差速器壳模型进行网格划分、差速器壳负载及边界条件的设定,计算求解得出差速器壳应变分布图及应力分布图,从而找出差速器壳易破坏部位,寻找到提高差速器壳强度的措施。设计差速器壳时,取用较大的过渡圆角,以提高其疲劳强度。
关键词:差速器壳,强度, PROE,ANSYS
Abstract
The differential case is one of the most important motion parts, which bears the most complex load, and continuously the differential case intensity analysis is valued by the designers. It is much too difficult to carry on the experimental study by the traditional method for the geometry shape of differential case, boundary condition and extremely complicated function load, so a new research technique to study and analyze differential case is requested to use.
PROE cartography software is utilized in this thesis to protract semiaxix three dimensional full-scale mockups, then the intensity analysis for the differential case by using ANSYS analysis software is carried on. The differential case strain distribution map and the stress distribution map are obtained through carrying on the grid division, the differential case load and the boundary condition hypothesis to the differential case model, thus the exposed destructive position in the differential case can be discovered, and some ways are seeked to enhance the differential case intensity. When designing the differential case, the bigger transition fillet can be used to enhance the anti-fatigue strength.
Key word: differential case , Intensity, ,PROE,ANSYS
目 录
1 引 言 1
1.1课题的背景 1
1.2差速器壳的研究现状 1
1.3 课题的主要研究内容及意义 1
2 差速器壳的三维实体建模 2
2.1 Pro/ENGINEER 概述 2
2.1.1 Pro/ENGINEER系统简介 4
2.1.2 Pro/ENGINEER系统特点 4
2.1.3 Pro/ENGINEER的应用现状 4
2.2 Pro/ENGINEER的工作环境和系统设置 4
2.2.1 硬件要求 5
2.2.2 操作系统设置 5
2.2.3 基本功能 7
2.3 差速器壳三维实体建模过程 9
3 差速器壳强度的有限元分析 23
3.1 ANSYS 概述 23
3.1.1 ANSYS简介 23
3.1.2 ANSYS的主要功能和技术特点 24
3.1.3 ANSYS的系统要求 24
3.1.4 ANSYS的基本分析过程 24
3.1.5 ANSYS的发展和应用 25
3.2 ANSYS菜单和窗口介绍 25
3.3 基于ANSYS差速器壳强度分析 27
结论 32
参考文献 33
致谢及声明 34
资料文件预览
共1文件夹,1个文件,文件总大小:1.63MB,压缩后大小:1.32MB
  • 毕业论文-汽车差速器壳的三维造型及有限元分析
    • Microsoft Word文档毕业论文-汽车差速器壳的三维造型及有限元分析.doc  [1.63MB]
下载地址
资料评论
注意事项
下载FAQ:
Q: 为什么我下载的文件打不开?
A: 本站所有资源如无特殊说明,解压密码都是www.xuehai.net,如果无法解压,请下载最新的WinRAR软件。
Q: 我的学海币不多了,如何获取学海币?
A: 上传优质资源可以获取学海币,详细见学海币规则
Q: 为什么我下载不了,但学海币却被扣了?
A: 由于下载人数众多,下载服务器做了并发的限制。请稍后再试,48小时内多次下载不会重复扣学海币。
下载本文件意味着您已经同意遵守以下协议
1. 文件的所有权益归上传用户所有。
2. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
3. 学海网仅提供交流平台,并不能对任何下载内容负责。
4. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
5. 本站不保证提供的下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
返回顶部