您现在正在浏览:首页 > 论文 > 机械机电 > 毕业设计-双筋蹄组合镗铰机床夹具设计

免费下载毕业设计-双筋蹄组合镗铰机床夹具设计

  • 资源类别:论文
  • 资源分类:机械机电
  • 适用专业:机械设计
  • 适用年级:高职
  • 上传用户:舞忆尘
  • 文件格式:word+AutoCAD
  • 文件大小:702.10KB
  • 上传时间:2009-3-21 20:23:43
  • 下载次数:0
  • 浏览次数:74

安全检测:瑞星:安全 诺顿:安全 卡巴:安全

资料简介
毕业设计 双筋蹄组合镗铰机床夹具设计 共30页,11703字 附零件图,装配图
摘 要:夹具主要依据零件的加工要求来设计的。夹具应满足零件加工工序的精度要求、加工生产率要求,并保证操作方便、安全及使用寿命和较低的夹具制造成本。本课题加工的零件是焊接件,总体呈拱形,两端分别有直径为20mm和30mm的孔,拱形的外缘有一高为100mm的肋板。零件的加工精度要求较低。
根据六点定位原理和定位基准的选择原则,采用长V型块,支承块和定位挡铁定位。长V型块置于拱形肋板后限制x轴的两自由度和z轴的两自由度,挡铁置于孔端限制绕y轴旋转的自由度,支承块置于肋板下方限制沿y轴移动的自由度。依据相关原理计算定位误差。根据夹紧方式的选择原则选择夹紧元件为压板压头和V型块,然后通过切削力进行夹紧力的计算。夹紧的动力装置选用液压装置。按照定位元件和夹紧元件设计连接件。因为刀杆较短,所以在本课题中导向元件设计就不作要求。然后进行其它元件和装置的设计。
根据以上元件和装置确定夹具总体布局和夹具体的结构形式,并处理好定位元件在夹具体上的位置。绘制夹具方案设计,进行工序精度分析。对以上设计进行审核。最后设计夹具总装配图。
关键词:夹具; 定位; 夹紧; 组合机床。
The design of the jig of double rebars and feet of modular machine
Abstract: The jig design is based on the request of parts working . the jig should satisfy the request of mading procedure precision , the processing productivity, and guarantee ease of operation, security ,service life and low production cost. This parts are the weldment in this task, the whole parts with two holes lying in head and foot whose the diameter respectively are 20mm and the 30mm assume the arch, the arch outflow boundary has a ribbed plate whose height is the 100mm. The parts processing precision is low.
According to six localizations principles and selection principle of the localization datum, using the long V block, the supporting block and the localization comes true the hard localization. The long V block putted in the arch ribbed plate to limit two degrees of freedom in x axis and the z axes two degrees of freedom, the iron putted in the hole end limit to the degree of freedom which circle the y rotation of axis, the supporting block putted under the ribbed plate to limit degree of freedom along the y axis migration. position error is reckoned by the correlation principle . According to the way of the selection principle , discharge head and V block is selected to clamp the part .Then Computation of the strength is achieved by carrying on through the cutting force clamps . The power of clamps is from the hydraulic unit. Design of bridge piece is according to the location part and the clamp part. The guide part designing in this topic is not requested because the cutter bar is short. Other parts and equipment is designed following last process.
The jig overall arrargement and concrete structure of the body clamp is determined with the above part and the equipment. The position of the components in the kits specific location must be guaranteed ,and then design the jig , carry on the working procedure precision analysis. The design review is following. Finally the jig assembly drawing is achieved.
Keywords: jig ; location; clamp; modular machine tool.
目 录
1 前言………………………………………………………………………………1
2 总体概述…………………………………………………………………3
2.1 工艺路线的确定………………………………………………………………3
2.2 机床夹具在组合机床的地位及作用……………………………………………4
2.3 总体设计中对夹具设计的重要的参数……………………… ………………………4
3 双筋蹄组合镗铰机床的夹具设计…………… …………………………………… …6
3.1概述………………………………………………………………6
3.1.1 机床夹具的分类……………………………………………………………6
3.1.2夹具的组成……………………………………………………………6
3.1.3 夹具体……………………………………………………………………6
3.1.4 机床夹具在机械加工中的作用……………………………………………7
3.1.5 国内外夹具的发展与趋势……………………………………………7
3.2 夹具设计要求与选型……………………………………………9
3.2.1夹具设计要求……………………………………………………………9
3.2.2 夹具的选型…………………………………………………………………9
3.3 定位和夹紧方案的确定…………………………………………………………11
3.3.1 定位和夹紧方案的选择分析…………………………………………………11
3.4 定位元件和夹紧元件的设计计算…………………………………………………15
3.4.1 定位元件的设计计算………………………………………………………………15
3.4.2 夹紧元件的设计计算……………………………………………………………16
3.5 误差的分析计算………………………………………………………18
3.5.1误差的计算…………………………………………………………………18
3.5.2 加工精度的保证…………………………………………………………………18
3.6 夹具机构的确定……………………………………………………………21
3.6.1 夹具体的确定…………………………………………………………………21
3.7 夹紧力的确定…………………………………………………………23
3.7.1 夹紧力的计算公式…………………………………………………………23
3.7.2 夹紧力的计算………………………………………………………………23
3.8 液压驱动装置的设计计算…………………………………………………………25
3.8.1 液压缸的设计计算…………………………………………………………25
3.8.2 活塞的设计…………………………………………………………………25
3.8.3 活塞杆的设计………………………………………………………………25
3.8.4导向套的设计………………………………………………………………25
3.8.5 密封元件的设计选择…………………………………………………………26
4 结论………………………………………………………………………………………27
致谢…………………………………………………………………………………28
参考文献……………………………………………………………………29
附录…………………………………………………………………………30
资料文件预览
共4文件夹,19个文件,文件总大小:1.69MB,压缩后大小:702.10KB
  • 毕业设计-双筋蹄组合镗铰机床夹具设计
    • 0210110408 倪绍流
      • 成果性材料
        • AutoLISP、CommonLISP和其他LISP语言文件acad.lsp  [2.77KB]
        • AutoCAD工程图纸文件V形块-陶俊2006.dwg  [47.93KB]
        • Microsoft Word文档中英文摘要-陶俊 2008.doc  [28.00KB]
        • AutoCAD工程图纸文件压板-陶俊2006.dwg  [56.73KB]
        • AutoCAD工程图纸文件夹具体-陶俊2006.dwg  [120.15KB]
        • AutoCAD工程图纸文件夹具总图-陶俊2006.dwg  [198.00KB]
        • AutoCAD工程图纸文件定位板-陶俊2006.dwg  [38.12KB]
        • AutoCAD工程图纸文件支架1-陶俊2006.dwg  [89.89KB]
        • AutoCAD工程图纸文件支架2-陶俊2006.dwg  [99.02KB]
        • Microsoft Word文档毕业设计说明书封面-陶俊 2008.doc  [20.00KB]
        • AutoCAD工程图纸文件法兰盘-陶俊2006.dwg  [80.21KB]
        • Microsoft Word文档目录-陶俊 2008..doc  [29.50KB]
        • Microsoft Word文档设计任务书-陶俊2008.doc  [83.50KB]
        • Microsoft Word文档说明书正文-陶俊 2008.doc  [401.50KB]
        • AutoCAD工程图纸文件铰链板-陶俊2006.dwg  [46.42KB]
      • 过程性材料
        • Microsoft Word文档文献资料-陶俊2008.doc  [26.00KB]
        • Microsoft Word文档毕业实习报告陶俊 2008.doc  [164.00KB]
        • Microsoft Word文档毕业设计开题报告-陶俊2008.doc  [171.00KB]
        • Microsoft Word文档毕业设计选题申报表-陶俊2008.doc  [31.50KB]
下载地址
资料评论
注意事项
下载FAQ:
Q: 为什么我下载的文件打不开?
A: 本站所有资源如无特殊说明,解压密码都是www.xuehai.net,如果无法解压,请下载最新的WinRAR软件。
Q: 我的学海币不多了,如何获取学海币?
A: 上传优质资源可以获取学海币,详细见学海币规则
Q: 为什么我下载不了,但学海币却被扣了?
A: 由于下载人数众多,下载服务器做了并发的限制。请稍后再试,48小时内多次下载不会重复扣学海币。
下载本文件意味着您已经同意遵守以下协议
1. 文件的所有权益归上传用户所有。
2. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
3. 学海网仅提供交流平台,并不能对任何下载内容负责。
4. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
5. 本站不保证提供的下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
返回顶部