您现在正在浏览:首页 > 论文 > 机械机电 > 毕业设计-薄煤层采煤机设计

免费下载毕业设计-薄煤层采煤机设计

  • 资源类别:论文
  • 资源分类:机械机电
  • 适用专业:机械设计制造及自动化
  • 适用年级:大学
  • 上传用户:595440588
  • 文件格式:word+Autocad
  • 文件大小:1.25MB
  • 上传时间:2011-5-16 15:16:45
  • 下载次数:2
  • 浏览次数:94

安全检测:瑞星:安全 诺顿:安全 卡巴:安全

资料简介
毕业设计-薄煤层采煤机设计,共53页,11256字,附设计图纸
摘 要
薄煤层工作面采高低,要求采煤机机身矮,且要有足够的功率,通常功率不应低于100~200kW;机身尽可能短,以适应煤层的起伏变化;要有足够的过煤和过机空间高度;尽可能实现工作面不用人工开切口进刀;有较强破岩过地质构造能力;结构简单、可靠,便于维护和安装。根据这些要求,薄煤层采煤机分为骑输送机式和爬底板式两类。骑输送机式采煤机由输送机机槽支承和导向,只能用于开采厚度大于0.8~0.9m 煤层。爬底板式采煤机机身位于滚筒开出的机道内,机面高度低,当采高相同时,与骑输送机式相比,过煤空间高,电机功率可以增大,具有较大生产能力,并且工作面过风断面大、工作安全,可用于开采0.6~0.8m的煤层,以前,薄煤层采煤机可选机型少,可靠性差,功率低,单产低,使我国薄煤层产量逐年减少,弃采严重,资源浪费大,从20世纪80年代开始,薄煤层采煤机从无到有得到稳定发展。随着薄煤层采煤机的推广应用,适用工作范围扩大,也暴露了许多缺陷和不足,限制了使用效果。根据薄煤层开采的迫切需要,不断加截割部功率和牵引部功装机功率开发适合国情的新一代大功率薄煤层采煤机是非常必要的。
关键词:薄煤层;爬底板;采煤机;截割部
Abstract
Thin seam mining height, required shearer body short, and have enough power, power is usually not less than 100 ~ 200kW; body as short as possible to meet the seam of the ups and downs; have had enough coal and the turbine room height; face as much as possible without artificial feeding to open incision; have a stronger ability to rock the geological structure; structure is simple, reliable, easy maintenance and installation. According to these requirements, thin seam miner into riding and climbing conveyor type floor type two. Riding conveyor Shearer slot machine by the conveyor and a guide bearing, only for mining coal seam thickness of more than 0.8 ~ 0.9m. Shearer fuselage floor crawling out of the machine in the drum channel, machine height is low, when the mining and height of the same time, compared with riding a conveyor type, high space than coal, electric power can be increased with larger production capability, and face through the wind section of a large, work safety, can be used in the coal mining 0.6 ~ 0.8m, before the optional model thin coal seam shearer less poor reliability, low power, low yields, so that thin coal production in China reduced year by year, abandoned mining serious waste of resources, large, from the 20th century, 80's, the thin coal seam shearer from scratch and have stability and development. With the wide application of thin coal miner, for expanding the scope of work, but also exposed the many flaws and shortcomings, limiting the results. According to the urgent need for thin coal seam, the continual increase in cutting the Department of Ministry of Power and traction power installed capacity of power development for a new generation of high-power thin seam conditions is necessary Shearer
Key words:Thin Seam;Crawl floor;Shearer;Cutting Department
目 录
摘 要 I
Abstract II
第1章 绪论 1
1.1 国内薄煤层采煤机发展概况 1
1.2 国外薄煤层采煤机发展状况 3
1.3 MG132/143-TPD采煤机的主要特点和应用领域 4
第2章 方案设计和选择 5
2.1 传动方案 5
2.2 传动方案的分析和选择 6
第3章 总体结构设计 7
3.1 设计目标 7
3.2 计算装机功率 7
3.3 总体参数的确定 10
3.3.1 总传动比的确定 10
3.3.2 齿轮模数和齿数的确定 10
3.3.3 截割部轴组件的设计 20
第4章 强度校核 23
4.1 齿轮强度校核 23
4.2 轴的校核 30
4.2.1 一轴的疲劳强度校核 30
4.2.2 二轴的疲劳强度校核 32
4.2.3 太阳轮轴的疲劳强度校核 33
4.2.4 滚筒轴的疲劳强度校核 34
4.2.5 惰轮轴的疲劳强度校核 37
4.2.6 行星轮轴的疲劳强度校核 38
4.3 滚动轴承的寿命校核 39
4.4 键的校核 41
结 论 44
致 谢 45
参考文献 46

已知参数:1、采高 =0.54 m(约等于滚筒直径D);2、截深J =0.8 m;3、采煤机机宽小于B =1.2 m;4、设计最大生产力Q =120t/h t/h;5、滚筒转数n 小于90 r/min;6、煤质f 小于3(A =240~300 N/mm)。
资料文件预览
共2文件夹,7个文件,文件总大小:2.92MB,压缩后大小:1.25MB
  • 毕业设计-薄煤层采煤机设计
    • 毕业设计
      • AutoCAD工程图纸文件太阳轮.dwg  [92.91KB]
      • AutoCAD工程图纸文件总的装配图1.dwg  [415.28KB]
      • AutoCAD工程图纸文件截一轴.dwg  [104.23KB]
      • AutoCAD工程图纸文件截二轴.dwg  [91.47KB]
      • Microsoft Word文档毕业论文1.doc  [1.92MB]
      • AutoCAD工程图纸文件直齿轮.dwg  [76.59KB]
      • AutoCAD工程图纸文件装配图.dwg  [242.09KB]
下载地址
资料评论
注意事项
下载FAQ:
Q: 为什么我下载的文件打不开?
A: 本站所有资源如无特殊说明,解压密码都是www.xuehai.net,如果无法解压,请下载最新的WinRAR软件。
Q: 我的学海币不多了,如何获取学海币?
A: 上传优质资源可以获取学海币,详细见学海币规则
Q: 为什么我下载不了,但学海币却被扣了?
A: 由于下载人数众多,下载服务器做了并发的限制。请稍后再试,48小时内多次下载不会重复扣学海币。
下载本文件意味着您已经同意遵守以下协议
1. 文件的所有权益归上传用户所有。
2. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
3. 学海网仅提供交流平台,并不能对任何下载内容负责。
4. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
5. 本站不保证提供的下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
返回顶部