您现在正在浏览:首页 > 论文 > 机械机电 > 毕业论文-心形灯饰塑料注塑模具设计

免费下载毕业论文-心形灯饰塑料注塑模具设计

  • 资源类别:论文
  • 资源分类:机械机电
  • 适用专业:模具设计
  • 适用年级:本科
  • 上传用户:jameak
  • 文件格式:word
  • 文件大小:346.61KB
  • 上传时间:2011-3-16 11:34:38
  • 下载次数:3
  • 浏览次数:247

安全检测:瑞星:安全 诺顿:安全 卡巴:安全

资料简介

毕业论文-心形灯饰塑料注塑模具设计,47页,22317字。
摘要
灯饰的形状较为复杂,所以模具设计中要考虑的因素有很多,除考虑它的出模、分型面,还需考虑它成型的质量,表面光洁度等。更重要的是考虑它的制造难度和成本。所以我们设计应认真分析塑料制品的结构,寻求最佳的设计方案。分型面的选择也很重要,制件不是平直表面,制件的形状很不规则,分型面的选择既要考虑不影响制件表面的美观,又要达到结构要求。由于制品体积比较大,所以浇注系统的设计也很重要,在此次设计中我选顶面侧浇口,并设有冷料穴。拉料杆采用倒锥形,这就解决了制品出模的问题。
关键词:分型面 成型 凸模 凹模 分型面
ABSTRACT
The reading lampthe shape of the cover than for complicacy, so want in the molding tool design the factor of the consideration have a lot of, a mold, cent type that divided by the consideration it, still need the consideration quantity that it model, surface clean an etc..More important consideration it of manufacturing difficulty with cost.So our design should analyze the construction that plastics product hard, design project looking for best. This time design most aims at the construction of the molding tool proceeded the design, because reading lampthe cover center contain a card dish, flank contain card door, so it must have the side take out organization, because of adopting a mold two space , so side take out construction I use two inclined lead the pillar guarantee, using inclined lead the pillar arouse the inclined slippery a sport, equiping the inclined slippery a smooth cent for, from but guaranteeing molding tool mold in fixed position with the fixed position.The choice of the cent type is too very important, a shape for is not straight and even surface, the piece of system is very irregular, the choice of the cent type since consider to do not affect a superficial beauty, attain the construction request again.Because producting the physical volume bigger, so sprinkle the design that note the system too very important, here a design inside I choose a side sprinkles, and establish the cold anticipating the cave.Pull to anticipate the pole adoption pour the form of Inclined, this resolved the problem of the ware a mold.
Key words:
Cent type Model Convex mold Cave mold Cent type

目录
1前言 5
2 注塑件的设计 6
2.1塑件(灯饰)模型图 6
2.2 材料选择 6
2.3 结构设计 7
表2-3 肋的圆角半径值关系表 9
2.4塑件的尺寸精度及表面质量 9
3 注塑成型的准备 10
3.1 注塑成型工艺简介 10
3.2 注塑成型工艺条件 12
3.3注塑机的选择 13
3.4 注射机的校核 16
4 模具设计 18
4.1 塑料配方说明 18
4.2 分型面的确定 19
4.3型腔数目的确定 20
4.4浇口确定 20
4.5模具材料的选择 20
4.6浇注系统设计 21
4.7模架的确定 25
4.8导向与定位机构 28
4.9顶出系统设计 28
4.10成型零件工作尺寸的计算 33
4.11排气设计 36
4.12温度调节系统设计 38
附录 46
致 谢: 48

资料文件预览
共1文件夹,1个文件,文件总大小:1.44MB,压缩后大小:346.61KB
  • 毕业论文-心形灯饰塑料注塑模具设计
    • Microsoft Word文档毕业论文-心形灯饰塑料注塑模具设计.doc  [1.44MB]
下载地址
资料评论
注意事项
下载FAQ:
Q: 为什么我下载的文件打不开?
A: 本站所有资源如无特殊说明,解压密码都是www.xuehai.net,如果无法解压,请下载最新的WinRAR软件。
Q: 我的学海币不多了,如何获取学海币?
A: 上传优质资源可以获取学海币,详细见学海币规则
Q: 为什么我下载不了,但学海币却被扣了?
A: 由于下载人数众多,下载服务器做了并发的限制。请稍后再试,48小时内多次下载不会重复扣学海币。
下载本文件意味着您已经同意遵守以下协议
1. 文件的所有权益归上传用户所有。
2. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
3. 学海网仅提供交流平台,并不能对任何下载内容负责。
4. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
5. 本站不保证提供的下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
返回顶部