学海网

毕业设计-汽车随车起重机设计，57页，18490字。附设计图纸、外文资料、外文翻译
一.设计题目:
汽车随车起重机设计
二． 设计任务要求及主要原始资料
任务要求：
1. 撰写论文
2. 起升机构的设计
3. 起重臂的设计
4. 回转机构的设计
5. 液压系统的设计
资料:《起重机械》 《起重运输机金属结构设计》
目 录
摘 要…………………………1
第一章 绪论…………………4
第一节 引言……………4
第二节 随车起重机方案比较与选用………4
第二章 起升机构的设计……8
第一节 起升机构的基本参数计算……8
第二节 钢丝绳的设计与选用10
第三节 滑轮及滑轮组设计………11
第四节 吊钩的设计与选用…13
第五节 卷筒设计………14
第六节 减速器设计……16
第三章 起重臂的设计………33
第一节 三铰点设计……33
第二节 起重臂设计……34
第四章 回转机构的设计……40
第一节 回转支承的选用40
第二节 回转减速器的选用……43
第三节 支腿反力的计算44
结论………………45
后记……………46
参考文献…………47
摘 要
6.3吨随车起重机属于架型起重机，它将起重和运输相结合，不仅节省劳动力，而且极大的减小了工作强度、提高了工作效率。本次毕业设计在6.3吨随车起重机上首次采用了伸缩臂型结构，并对起重机臂进行了优化设计。它具有结构紧凑、易于操作的特点，可广泛用于交通运输、港口、仓库、以及所有中小型工业货物装卸与远距离运输之中。
本文主要内容如下：
起升机构设计 起升机构包括液压马达、减速机、棘轮停止器和卷筒。减速机用来降低液压马达驱动速度，卷筒用于绕进或放出钢丝绳。机构工作时，液压马达驱动减速机，减速机的低速轴带动卷筒，将钢丝绳卷上或放出，经过滑轮组系统使载荷实现上升或下降，其升降由马达的旋转方向而定，通过棘轮停止器实现制动。
起重臂设计 起重臂采用伸缩式、箱形结构。箱形结构内装有伸缩油缸，臂的每个外节段内装有滑块支座，因此起重机的变幅可通过液压缸实现。为了减轻吊臂自重，充分发挥钢材的作用，吊臂的不同部位采用不同强度的钢材。
回转机构设计 回转机构由回转支承装置和回转驱动装置组成。即一对脂润滑的回转支承装置、蜗轮旋杆减速机和液压马达。这种结构自重轻、受力合理、运行平稳，可以使机构在水平面内运输货物。
[关键词]: 随车起重机 起升机构 起重臂 回转机构 回转支承
Abstract
6.3Truck Mounted Crane (abbreviation TMC) belongs to boom-Crane .It combines the advantages .So it can greatly decrease labor intensity, increase working I use flexible boom in TMC for the first time and have a optimization design. This product has features of compact structure, easy operation. It is suitable for wide use in traffic transportantion,dock warehouse and all small-sized industries for goods loading loading and unloading and long distance transportation. Its main content includes the following aspects:
The design for winch mechanism The winch mechanism consists of hydraulic motor, reducer, ratchet wheel stop and winch drum.Reducer lowers the speed of hydraulic motor for driving the winch drum to wind or unwind the load hoisting wire rope. When working, the motor drives reducer and bring along winch drum rotation, then the wire rope is wound or unwound ,the load will be lift or lowered through pulley block system. Lifting or lowering of the load will be controlled by the rotation direction of the motor. Ratchet wheel stop is used to stop the motion of the drum, holding the load in the air.
The design of boom The boom adopts flexible type and box-shaped structure.Cylinder bodies are fitted on the boom. There are slide supports at outsides of every section of booms. The working range of TMC can outsides of every are fitted on the boom.There are slide supports at outsides of every section of booms. The working range of TMC can be realized by the extension or retraction of cylinder body. It uses different steel products in different positions for decrcasing boom’s weight and fully developing steel products’ function.
The design of swing mechanism Swing mechanism contains swing bearing and swing driver, the same is, no-oil lubricated bearings, worm-and-wheel steering gear and gydraulic motor. This structure has the advantages of light weight, reliable force on it and smooth action. It can make the load transported in the horizontal plane.
Key words TruckMounted Crane winch mechanism Boom swing mechanism Swing bearing